Polyethersulfone (PES) Nest syringe filters have pore size either 0.22µm or 0.45µm, and diameter 13mm or 25mm, with membrane materials either with PES or PVDF membranes. For sample volumes of 2mL to 100mL. Retention volume <115µL. Maximum operating temperature: 100°C autoclave at 125°C for 15 min. Maximum operating pressure approximately
Minisart ® NML Syringe Filters provide the optimal method for clarification and sterilization of liquids, robustly removing bacteria and particles, without any impact on product quality or loss of target molecule. Superior filter areas up to 6.2 cm 2. 0.1µm to 5µm pore sizes. Low adsorption characteristics.
Syringe Filters Non-sterile HIXWER Syringe filters are developed under production processes with strict quality controls, assuring a safe and reliable product for your laboratory analysis. They are used to filter small volumes of aqueous solutions, aggressive gases and air in hydrophobic vents.
Syringe filters with cellulose acetate or polyethersulfone membranes are ideal for sterile filtration of buffers, tissue culture media or additives, and other biologicals. The polyethersulfone membrane offers high flow rates. Nonsterile syringe filters are excellent for HPLC applications. Each filter has a female Luer-lock inlet and a male slip
Syringe filters are single use, self contained, filtration devices that are typically used to remove contaminating particulate from liquids or gasses. When selecting the correct syringe filter for an application there are a number of factors to consider, these include: Filter and housing materials. Pore size. Effective filtration area.
Choose a 13mm diameter barrel for 10mL samples and a 25mm barrel for 100mL samples. For inquiries and assistance, you can reach us at 1 800-878-7654 (Customer Service Line), 707-525-5788 (Local), +31 20 638 05 97 (Europe) or email Sales@CPIInternational.com.
The pore size of your syringe filter is determined by the size of the particles you need to filter out of your aqueous solution. Syringe filters for aqueous solutions are available in these pore sizes: 0.05 µm, 0.10 µm, 0.22 µm, 0.45 µm, 0.70 µm, 0.80 µm, 1 µm, 3 µm, 5 µm, and 10 µm . As a guide, the finer the pore, the more pressure
A syringe filter (or wheel filter) is a single-use, membrane-based device used for the removal of particulate impurities from small (≤ 100 mL) liquid samples ( Figure 1 ). Selected based upon the desired end application, disposable syringe filters are commonly used in labs for fast and efficient filtering, material purification, or even
Feb 17, 2020 · Step 2: Attach a syringe filter to the Syringe. Open the syringe filter package so that you can later pick the filter up easily, especially for individually packed sterile syringe filters. a. For sample volume < 10 mL. Draw a small amount of air (about 1 mL) into the syringe before loading the sample solution.
A syringe filter with a 0.45 μm pore size achieved the highest recovery rate (0.29%), while polycarbonate membrane filters with pore sizes of 0.6 μm and 0.4 μm recovered less Campylobacter, at 0.01% and 1.3 × 10 -3 %, respectively. We also tested 601 diarrheic stool samples using membrane and syringe filtration methods.
Millex® Syringe filters set the standard for reliable small volume filtration (1 mL to 200 mL). Available in 4, 13, 25, 33, and 50 mm diameters. Minimal hold-up volume for less sample loss o f small volumes and are ideal for solutions such as antibiotics and tissue culture additives. Their unsurpassed quality and consistency of results has led
Water and acetonitrile were passed through polypropylene or PTFE syringe filters (as indicated in legend), then used 1:1 (v/v) to prepare the mobile phase for UHPLC. The system was run at 0.25 mL/min for 600 min with backpressure recorded every 50 min. DP represents total change in backpressure after 600 min.
Puradisc™ FP Syringe Filter. Syringe Filter, Puradisc™ FP, 1.2 µm Pore Size, Up to 100 ml, 26 x 34 mm, 30 mm dia Membrane, Cellulose Acetate Membrane, Sterile, Polycarbonate Housing Material, Autoclavable, For Routine Syringe Filtration. Syringe Filter, Puradisc™ FP, 1.2 µm Pore Size, Up to 100 ml, 26 More SECO Part #: 12-4458-05.
Syringe filters are generally a necessary laboratory supply that may be applied over a broad spectrum of research laboratory procedures. They tend to be generally utilized in the preparation of aqueous and organic solutions, in which it is important to have quick and efficient filtration. Syringe filters will also be needed for the biotech
Use these all-plastic disposable syringes with your Titan3, Target2, and Choice Basic syringe filters. Comprising a polypropylene barrel and polyethylene plunger, these syringes eliminate problems with rubber or synthetic plunger gaskets and requires no silicone or oil lubricant in the barrel. Choose from in 1, 3, 5, 10, 20, 30, and 50 mL sizes.
Material: USP Type 1, Class A, 33 Borosilicate Glass
Volume: 2ml (standard volume) 1.5ml(actual volume)
Application: HPLC and GC system
Dimensions: 11.6 x 32mm
Neck Diameter: 8mm
Qty/Pack: 100pcs/pack
Payment: T/T
MOQ: 1pack
Material: USP Type 1, Class A, 33 Borosilicate Glass
Volume: 2ml (standard volume) 1.5ml(actual volume)
Application: HPLC and GC system
Dimensions: 11.6 x 32mm
Neck Diameter: 9mm
Qty/Pack: 100pcs/pack
Payment: T/T
MOQ: 1pack
Material: USP Type 1, Class A, 33 Borosilicate Glass
Volume: 2ml (standard volume) 1.5ml(actual volume)
Application: HPLC and GC system
Dimensions: 11.6 x 32mm
Neck Diameter: 10mm
Qty/Pack: 100pcs/pack
Payment: T/T
MOQ: 1pack
Material: USP Type 1, Class A, 33 Borosilicate Glass
Volume: 2ml (standard volume) 1.5ml(actual volume)
Application: HPLC and GC system
Dimensions: 11.6 x 32mm
Neck Diameter: 11mm
Qty/Pack: 100pcs/pack
Payment: T/T
MOQ: 1pack