13, 17, 25 & 31mm: Female luer lock inlet, male slip luer outlet Typical Hold-Up Volume (with air purge) 13 mm: < 15 μL 17mm : < 18 μL 25 mm: < 80 μL 25 mm Prefilter: < 80 μL 31 mm: < 80 μL Maximum Operating Temperature 55 °C (131 °F) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure 13 mm: 6.9 bar (690 kPa, 100 psi) 17 mm: 130 psi

Luer Lock, MNPT, FNPT, Tri clamp, and Quick ouplings Operating onditions Max. differential pressure: 30 psid (2 bar) Maximum Operating Pressure Liquid: 60 psig @ 77° F (4 ar @ 25° ) Maximum Operating Pressure Gas: 30 psig @ 77° F (2 ar @ 25° ) Maximum Operating Temperature: 60° Effective Filtration Area 13mm - 0.1247in2 (0.8cm2)

Filter Type: D25 mm: Quantity per Pack: 100: Pore Size: 1 µm: Sterilization: Nonsterile: Inlet / Outlet: Female Luer Lock / Male Luer Lock: Housing Material: Polypropylene: Burst Pressure (psi) 87: Filtration Area (cm2) ≥4.9 cm2: Maximum Operating Temperature: 60 Degrees C / 140 Degrees F: Maximum Operating Pressure (@23 Degrees C) 5.2bar

13 and 25 mm: Female luer lock inlet, male slip luer outlet Typical Hold-Up Volume (with air purge) 13 mm: < 15 µL 25 mm: < 125 µL 25 mm prefilter: < 150 µL Maximum Operating Temperature 55 °C (131 °F) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure 13 mm: 6.9 bar (690 kPa, 100 psi)

Female luer lock inlet, male slip luer outlet Typical Hold-Up Volume (with air purge) < 125 µL Maximum Operating Temperature 82 °C (180 °F) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure 4.1 bar (410 kPa, 60 psi) at 21 - 24 ºC (70 - 75 ºF) 2.1 bar (210 kPa, 30 psi) at 82 ºC (180 ºF) Typical Water Flow Rate

Inlet Female luer lock tab Female luer screw Female luer screw Outlet Male luer slip Male luer slip Male luer slip Pre-filter N Selected membranes Selected membranes 4 mm Target2 17 mm Target2 30 mm Target2 Housing Polypropylene Polypropylene Polypropylene Filtration area 0.125 cm2 1.6 cm2 4.9 cm2 Maximum pressure 5.5 BAR 8 BAR 10 BAR

Female luer lock inlet, male slip luer outlet Typical Hold-Up Volume (with air purge) 25 mm PSF GxF: 200 µL 32 mm: 100 µL Maximum Operating Temperature 25 mm PSF GxF: 100 ºC (212 ºF) at 2.1 bar (210 kPa, 30 psi) 32 mm: 55 °C (131 °F) Maximum Operating Pressure

Operating Conditions Maximum Operating Pressure: Liquid: 5.5 bar (80psi) at 77°F/25°C Gas: 4.1 bar (60psi) at 77°F/25°C Minimum Burst Pressure: 8.3 bar (120psi) at 77°F/25°C Maximum Forward Differential Pressure: 4.21 bar (60psi) at 68°F/20°C Maximum Reverse Differential Pressure: 2.1 bar (30psi) at 68°F/20°C

Filter Media: hydrophobic PTFE 0.2μm. Housing: Clear medical grade ABS. Inlet/Outlet Connections. Inlet: FLL Female Luer Lock. Outlet: MLL Male Luer Lock. Effective Filtration Area (EFA) 1.7cm² PTFE membrane. Minimum Air Flow Rate. 30ml/min@ΔP=12mbar. Maximum Operating Pressure. 3.5 bar. Sterilization Compatibility. EtO, gamma irradiation

52.3 With the axis of the lock fitting horizontal, seal the assembly outlet and bring the internal water pressure to an effective pressure of 300 kPa to 330 kPa and maintain the pressure for 30 s. If the intended use is on a device employing higher pressure, then this shall be taken into consideration during testing.

Check Valves with Quick-Turn Fittings. Also known as luer lock couplings, quick-turn fittings consist of a plug and a socket that connect with a half turn, so you can easily connect and disconnect your line. These valves open to allow flow in one direction and close when flow stops or reverses. The clear body allows you to visually inspect flow

Effective Filtration Area: 3.9 cm 2; Sample Volume: < 150 mL; Inlet/Outlet Connections: Female luer lock inlet, male slip luer outlet; Typical Hold-Up Volume (with air purge): < 125 μL; Maximum Operating Temperature: 82°C (180°F) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure: 4.1 bar (410 kPa, 60 psi) at 21 - 24ºC (70 - 75ºF)

Female luer lock inlet, Male slip luer outlet: Maximum Operating Temperature: Maximum 100 °C (212 °F) at 2.1 bar (210 kPa, 30 psi) Sterilization: Provided non-sterile. If needed, autoclave at 121°C (250°F) at 1.0 bar (100 kPa, 15 psi) for a maximum of 15 min.

Female luer lock inlet, male slip luer outlet 10 µm: 82 ºC (180 ºF) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure 4 and 13 mm: 5.2 bar (520 kPa, 75 ...

60 PSID (4.1 bar) at 68°F (20°C) Maximum reverse differential pressure: 30 PSID (2.1 bar) at 68°F (20°C) Maximum Operating Temperature: PP & Gamma PP: 176°F/80°C HDPE: 140°F/60°C PVC: 122°F/50°C Regulatory Compliance The discs are manufactured from materials that conform to the requirements of 21CFR Part 177 of the U.S. Code of