high flow rates. The filter housings are suitable for operating flow rates of 60 m3/h to 19,200 m3/h. Cost-effective Solutions in Industrial Quality Air and Gas Filter Housings P-EG housings comply with the applicable guidelines: Compliant according to Manufactured by Technical Data P-EG Housings Size Capacity [m3/h] at 7 bar ope-rating pressure*

Maximum Operating Pressure 58 psig @ 77°F (4 bar @ 25°C) Maximum DiFerential Pressure 28 psid @ 77°F (1.9 bar @ 25°C) Maximum Operating Temperature 104°F (40°C) Absolute Removal Ratings (nm) 5, 10, 20, 50, and 100 5, 10 10, 40 Filter Cartridge Integrity All Filters are Tested prior to release

Filtrate: Filtrate is the water that has passed through the membrane. , i.e., the water passing through the membrane, per unit area of membrane: Equation 1. Where: J = flux, L/hr/m 2 (gal/d/ft 2) or Lmh (gfd) Qp = filtrate flow rate through membrane, L/hr (gal/d) Am = surface area of membrane, m 2 (ft 2) Note that the flux unit of L/hr/m 2 is

Maximum Operating Pressure. 13 mm: 6.3 bar (630 kPa, 90 psi) 25 mm PSF: 4.1 bar (410 kPa, 60 psi) at 21 - 24 ºC (70 - 75 ºF); 2.1 bar (210 kPa, 30 psi) at 55 ºC (131 ºF) Typical Water Flow Rate. mL/min at 0.7 bar (70 kPa, 10 psi) 13 mm, 0.2 µm: 17; 13 mm, 0.45 µm: 28; mL/min at 2.1 bar (210 kPa, 30 psi) Acrodisc One: 0.2 µm: 151 0.45 µm: 263

For flow rates up to 15 LPM we offer our GMS205 Series. This series uses the same user friendly design as the GMS105 series, but with a larger membrane. The increased surface area provides higher flows and also increases the time between service intervals. Our standard assemblies are machined from 316L stainless steel and supplied with Viton seals. Each assembly is supplied with an Hydrophobic

– ∆P Filter value is subsequently reset each time the blood flow rate is changed The operating points for TMP and Pressure Drop are recalculated during treatment USMP/MG120/19-0012 05/19

Jan 16, 2017 · exceptional high flow rate. Sartobind MA 75 units contain 15 membrane layers and have been developed for bind and elute and flowthrough applications at high flow rate. Sartobind MA 100 units with 5 membrane layers can be used for screening of buffer conditions and quantitative work at exceptional high flow rate.

Maximum Operating Temperature and Pressure. 2.1 bar (210 kPa, 30 psi) at 60 °C (140 °F) or 5.5 bar (550 kPa, 80 psi) at 21 - 24 °C (70 - 75 °F) Typical Differential Pressure < 0.07 bar (7 kPa, 1 psi) @ 1 mL/min; Mean Flow Rate. 1 - 4 mL/min; flow rate will vary with type of solutions, concentration of proteins, and other components; Typical

Maximum Operating 4.1 bar (410 kPa, 60 psi) 5.2 bar (520 kPa, 75 psi) 4.1 bar (410 kPa, 60 psi) Pressure at ambient temperature at ambient temperature at ambient temperature Recommended Minimum Bubble Point (Methanol): N/A Minimum Bubble Point Integrity Test 0.9 bar (90 kPa, 13 psi) [60% IPA/40% Water (v:v)]: Minimum Water Breakthrough: 0.8 bar

Maximum Operating Pressure 4.1 bar (410 kPa, 60 psi) at 21 - 24 ºC (70 - 75 ºF) 2.1 bar (210 kPa, 30 psi) at 82 ºC (180 ºF) Typical Water Flow Rate 795 mL/min at 1.0 bar (100 kPa, 15 psi) Related Products 47 mm Filter Funnels, Glass HPLC Mobile Phase Filtration Membranes SolVac® Filter Holder Stainless Steel Forceps Vacuum/Pressure Pumps

Diameter 25 mm Filtration Area 3.9 cm² Filter Media Hydrophobic PTFE Flow Rate 245 mL/min at 1.0 bar (100 kPa, 15 psi) Hold-Up Volume <125 µL Housings Polypropylene Maximum Operating Pressure 2.1 bar Max.

Maximum Operating Temperature 60 °C (140 °F) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure 4.1 bar (410 kPa, 60 psi) at ambient temperature Recommended Integrity Test Minimum Bubble Point - 60% IPA/40% H2O (v:v) 1.2 bar (120 kPa, 18 psi) Typical Liquid Flow Rate (1 cp) 0.8 L/min/0.1 bar (10 kPa) 0.6 L/min/psi Typical Air Flow Rate

Maximum Operating Temperature: 55°C (131°F) Maximum Operating Pressure: 0.2 and 0.45µm is 6.9 bar (100psi) GF/0.45µm is 6.3 bar (90 psi) Typical Water Flow Rate (mL/min at 2.1 bar (30psi)) 0.2µm, 25mm is 60 0.45µm, 25mm is 65 0.45µm, 25mm GF is 60: Typical Water Flow Rate (mL/min at 0.7 bar (10psi)) 0.2µm, 13mm is 17 0.45µm, 13mm is 28

30 psid @ 176 °F (2.1 bar @ 80 °C) Max. differential pressure reverse 40 psid @ 70°F (2.8 bar @ 21°C) Recommended change-out pressure 35 psid (2.4 bar) Eaton’s LOFMEM W membrane filter cartridges are the preferred choice for general water filtration, as a DI water prefilter/ postfilter and for use in aqueous-based Filtration Products

similar feed/concentrate flow rate per vessel through the length of the system and to maintain feed/concentrate flow within the limits specified for a given type of membrane element. Very high flow through a pressure vessel will result in a high pressure drop and possible structural damage of the element. Very low flow