(based on unit mass) () 2 / 2 1 2 2 2 1 u u p p − = − P u u = − 2 2 1 2 2 P u u u = − 2 1 2 2 1 2 2 Now if the fluid is incompressible the volume flow-rate will be the same at A and B. 2 2 1 1 u A u A Q = = 1 2 2 1 A A u u = Now A 2 /A 1 is the ratio of the areas of restriction to flow and is a constant which can be denoted m.

Maximum Allowable Back Pressure 2 bar (29 psi) at 20°C; 1.5 bar (21.8 psi) at 50°C (126) 2 bar (29 psi) at 20°C (39)

Feb 24, 2022 · The maximum contact pressure needed for achieving a conformal interface is determined by the Young’s modulus and the membrane thickness following the relationship π 2 4 P 0 2 1 − v 1 2 E 1 + 1 − v 2 2 E 2 2 1 / 3 + π 2 8 P 0 1 − v 1 2 E 1 r curve 3 t 3 = 1

Maximum Operating Pressure: 1.4 to 2.1 MPa, 200 to 300 psi, 13.8 to 20.7 bar Hose I.D. (size): -3 to -32 Nominal Hose Inside Diameter: 7 to 50 mm

Operating Parameters Maximum Working Pressure: 5.5 bar (80 Psi) @ 25 oC (77 oF) Maximum differential Pressure (forward): 4.1 bar (60 Psi) @ 25 oC (77 oF) oMaximum differential Pressure (reverse): 2.1 bar (30 Psi) @ 25 C (77 oF) oMaximum Operating Temperature: 80 C (176 oF) Recommended Replacement Pressure: 2.4 bar (35.3 Psi) Safety

GH Polypro (GHP) Membrane Disc Filters - GH Maximum Operating Temperature. 55 °C (131 °F) Minimum Bubble Point - IPA. 0.2 µm: 1 bar (100 kPa, 14.5 psi) 0.45 ...

Polypropylene (PP) is a rigid and crystalline thermoplastic used widely in everyday objects like packaging trays, household products, battery cases, medical devices, etc. Explore this comprehensive guide and learn everything you need to know about this widely used thermoplastic.

Feb 01, 2022 · For the GH membrane experiments were also performed in order to improve the purification and concentration of compounds of interest through a combination of diafiltration and batch concentration mode in selected operating conditions (TMP, 15 bar; T, 28 °C; Q f, 5.15 L/min) until to a diafiltration volume of 5 and a VRF of 2.0, respectively.

Mar 08, 2022 · In the most recent study ( Kurth et al, 2018) a net flux of up to 381 LMH was assumed (based on the outcomes of a pilot trial) along with an implied cost of ∼$175 USD per m 2 for the ceramic membrane, compared with $35 USD m −2 for the polymeric one operating at a net flux of 68 LMH.

Pore Size 0.2 μm Inlet/Outlet Connections Female luer lock inlet, male slip luer outlet Membrane Bed Volume 0.12 mL Maximum Operating Temperature and Pressure 2.1 bar (210 kPa, 30 psi) at 60 °C (140 °F) or 5.5 bar (550 kPa, 80 psi) at 21 - 24 °C (70 - 75 °F) Typical Differential Pressure < 0.07 bar (7 kPa, 1 psi) @ 1 mL/min Mean Flow Rate

Maximum Operating Pressure (bar) 2.1 bar. Maximum Operating Temperature (Metric) 100 °C. PTFE is a hydrophobic membrane, so it will repel water and is not ...

It is the identical final 0.2 µm membrane layer which ensures sterility of your product. But it is the pre-filter porosity which makes the difference. Depending on specific product properties a finer or coarser pre-filter layer can significantly improve the capacity of the filter.

Maximum ion exchange capacity and ionic conductivity for the composite membranes were obtained as 2.84 mmol/g and 80.2 mS/cm (50 °C) which was 21% and 47% higher as compared to pure ImPS membrane.

Membrane tubing – Nafion® Maximum operating pressure: 3 Bar Absolute Operating fluid temperature range: 1 to 80°C (33 to 176°F) Pressure differential on tubing: 35 kPa (0 to 5 psid) @ 80°C (176°F) Negative pressure differential will collapse tubing and must be avoided Storage temperature range: -30 to 60°C (-22 to 140°F)

Nov 05, 2018 · Maximum forward differential pressure. 0.34 MPa (3.4 bar; 50 psid) @ 25°C (77°F) Maximum reverse pressure. 0.21 MPa (2.1 bar; 30 psi) @ 25°C (77°F) Maximum operating temperature. 70°C (158°F) @ 30 psi. 70°C (158°F) @ 23 psi. Reference Materials Product Documentation. Published Nov 5, 2018 Data Sheet Intercept® Liquid Filters.